Short Circuit 3 – The primary objective is to ensure the factories used to produce products for VF in Bangladesh are safe for all of the workers employed. From broken and free electrical wiring association, particularly the wiring of dry iron utilized for CREASING PURPOSE. It is discovered that more often than not the iron wiring are appropriately settled while being continually utilized. The free wiring association gets in contact with negative and positive wires of iron, which gives start and odds of flame and electrical stun is high. Read about General Guidelines for UPS . …
Lint Built UPS
Build up constructed ups on overhead wiring channels.
Build up constructed ups inside electrical control boards.
Most normal build up constructed ups are inside sewing machine electrical engine packaging. Generally because of variance in current supply or because of Short Circuit 3 smoke ascends from these engine packaging, which laborers on observing this gets terrified.
Utilization of inflammable synthetic substances for spot expelling/Cleaning reason:
The most widely recognized concoction utilized for spot expelling is THINNER (Sprite containing
100% Alcohol) the gear utilized for showering has an electrical attractive engine.
Normally, because of steady use, these types of gear are anything but difficult to get overheated and
odds of start are high. Then again odds of flame are likewise high.
We as a whole think about flame in CHOWDHURY KNIT. The fundamental driver of flame was because of this
concoction utilized for spot expelling.
synthetic concoctions in washing plant and coloring plant are put away unsystematically and void
synthetic concoctions drums/compartments are normally held under open sky. Exceptionally in the event that corrosive drums are held under open sky and on the off chance that it downpours , exhaust may ascend from these holders and may cause fire and furthermore that these might be dangerous to wellbeing and condition.
Specialists absence of flame security learning and fire penetrates because of which if there should be an occurrence of genuine fire
or on the other hand because of any false caution they get apprehensive and froze.
Plants holding the ways out safely guarded.
Blocked Aisles/exits/staircases.
We can recognize the previously mentioned focuses as the principle and real reason for flame and losses in Bangladeshi processing plants. When we have distinguished the purposes behind flame and losses, we ought to do the accompanying, as we have confidence in “PREVENTATION IS BETTER THAN CURE” in view of these , all industrial facilities should:
Evacuate and supplant every single flawed wiring.
At any rate check and keep record of wiring support fortnightly.
Extraordinary checks to be directed on Iron, combining machine, free attachments, switches, Short Circuit 3 breakers on regular schedule and wherever change required ought to quickly be supplanted.
Clean build up assembled ups once per week.
Check and clean engine packaging once every week.
Correct all free electrical associations.
Choose affirmed and authorized Short Circuit 3 tester to complete all the previously mentioned works.
Give preparing to specialists and dishearten them on utilizing of any broken types of gear, they ought to be prepared to ready to perceive any kind of variation from the norm in the types of gear they are taking care of.
Store synthetics according to guidelines put on their holders.
Try not to dump any void synthetic holders under open sky.
In the wake of perceiving the reasons and reasons for flame in Bangladesh, we can classified the
Manufacturing plants in Bangladesh into sort dependent on their areas:
Freestanding Factory and its requirement for fire preventions.
A freestanding factory is factory which may be a single storied shed type building or it may be a multi storied building which is being used by one single factory and which is not shared by any other tenants. We can chalk out procedure and methods for free standing factories on how to tackle fire situations and how to train workers on these issues as follows;
Factory should conduct unannounced fire drills at least once a month.
factory should let the workers know about the accidents occurred in other factories and the reason of casualties, and educated them how to tackle in situations that had occurred in that factory and also educated and motivate workers to participate in Fire drills seriously.
At least 40% of workers should be trained on how to use fire extinguishers, but would be suggestible that as part of factories best policy 100% of workers should be trained on use of fire extinguishers. Factory to form “Disaster Management and Prevention Committee” with the following teams who should be provided with uniforms:
Fire Fighting team
Rescue team
Rescue team for Child care center
Special Security team
The above team members should be properly trained and they should have their own written
DISASTER MANAGEMENT AND PREVENTION PROCEDURE, these teams should sit for
meeting at least once a month.Educate all workers the meaning and importance of exit/aisles/extinguishers and electrical panels markings
Factory should install battery operated fire alarm system and this should be heard all at a time from all floors of the building no matter where activated from. In case of gong bell, workers should be trained that whenever one hears a gong bell ring should immediately start ringing the other gong bell in the floor by person near to the bell and workers to evacuated building as per procedure.
Factory to implement a system that electrician should check all electrical switches, irons, fusing machines etc., and sign out in a log book before shutting down the main switches on closing down of the factories.
All workers should know how to shut down main switches and how to activate fire alarm switches. Workers should be able to understand evacuation floor plan and should know the nearest exit to be used during evacuation.
Tenants Factory and its requirement for fire preventions.
Inhabitant manufacturing plant is a processing plant where the building is shared by different inhabitants or occupants and the fundamental passageway and ways out are altogether utilized usually. For Tenant kind processing plant every one of the focuses referenced for Freestanding processing plant is to be tracked with the accompanying focuses:
Should frame “Occupant DISASTER MANAGEMENT AND PREVENTION
Board of trustees”Should lead Fire penetrates and preparing together with different inhabitants . Guarantee that all staircases and ways out are kept clear unsurpassed. Have normal or public putting out fires hardware put at all stairwells, and crisis lights too. The fire caution alarm/signal/ringer ought to be gotten notification from all floors (all inhabitants) The occupant debacle the board and anticipation advisory group ought to sit for a gathering each month and should visit the entire working to discover resistance issues and they should take appropriate measure to amend the rebelliousness issues quickly.
Lead mindfulness meeting on these resistance issues. Blurbs/photos on security issues, for example, which means of different markings (exits/dousers/passageways and so forth) ought to be posted set up where by and large the consideration of laborers can be drawn.
Conclusion
Direct preparing ablaze wellbeing and medical problems of short circuit 3. direct reported and unannounced fire drills, board of trustees ought to encourage approaches to enhance if bore is nit agreeable. co-work with BGMEA and different purchasers to actualize the fire security, fire bore and preparing for all occupants inside a similar building.
With due regards it is to inform that, we are “Source Engineering” engaged with Manufacturing of Electrical Sub-station Equipments as H.T. Switchgear Panel (LBS/VCB), L.T. Switchgear Panel (MCCB/ACB), Main Distribution Board (MDB/SDB), Power Factor Improvement Plant (P.F.I. Plant), Also Supplier of Distribution Transformer (100KVA – 2000KVA), Auto Voltage Regulator, Industrial Voltage Stabilizer etc. Maintenance work facilities similar to: Sub-station Equipments Servicing, Generator / Lift Servicing and Flat Individual wiring facilities. In addition, we do Annual Maintenance Contract (AMC) for Electrical Equipments.
Generally followed aluminum channel cabling systems partially supported in sanitary PVC conduits & Flexible conduits. The electrical system in the factory has VCB protection as the main control and the changeover switch is manual type. Each SDB’s has its own MCCB as protection. The factory generally followed wiring systems supported in overhead aluminum channel above the working tables in production areas. The lighting fixtures are also supported in the overhead aluminum channel. There are some areas where surface PVC conduit, flexible conduit and concealed conduit wiring system have been used. The distribution wiring in aluminum channel installed in production areas is presented Also we are available for Electrical / House wiring solution with great expertise. (You can make a call to us for Free Inspection of your premises).
“Source” is an authorized dealer for Power Factor Capacitors & Relay of Frako, Germany and LS, Korea Brand. We Use Circuit Breaker Brand ofABB Italy/Germany. As China product dealer in support of : ChiNT, China, Electrical goods as MCCB, MCB, RCB, Magnetic Contactor, Power Capacitors, Relay, Switch/Socket etc.
More we supply Desktop Computer Full Setup, Accessories, Service on call and Maintenance work with IT related service work. The factory is operated & maintained by in-house electrical and maintenance team. However the maintenance of major equipment like generator is outsourced to the service centers. The factory is manned by electrical technicians to carry out the operation and maintenance tasks. The maintenance of electrical systems is being carried out on a regular basis.
They have still a lot of areas where periodical maintenance and electrical tests is required. The table below summarizes the major electrical safety issues identified during the inspection. Recommendations have been provided to each finding. The implementation schedule shall be developed by the factory to remediate each of the findings. The specific timing of improvements, including any requested extensions due to design / installation constraints, shall be submitted to the Audit for an approval.
Distribution panel needs to be cleaned for lint and dirt. Further, it is observed that the opening inside the panel board is also not sealed properly for vermin proof.
More than ever we serviced at Apartments premises, Commercial Buildings, Cold Storage, Embassy’s etc. for their Power Factor Cost reducing. If you have any PFC Charge at your common bill please follow up the bill and confirm that its reason of PFI Plant nonstandard operation.
Some of our regular client’s as follows: Bangladesh Red Crescent Society Bhaban, Embassy of the Federal Republic of Germany, Ambassador Residence (German), Australian High Commission, Canadian High Commission, Indonesian High Commission, Crescent Tower, Far-East Islami Life Insurance, Shanin Group of Co., Surmi Cold Storage Ltd, A.N. Khan Cold Storage Ltd., Punot Cold Storage Ltd., Chowdhury Leather Co. Ltd., Luna Indus. Accessories Ltd., Twin Tower Shopping Complex and many other Apartment Owner’s Association in Dhaka.
Therefore, we are here to serve you the right choice of your products and further elaboration to execute the service according to your demand.
AB Engineering & Services is an industrial power control company & automation engineering company in Bangladesh. We are manufacturer, supplier and importer of world class Electrical & Electronic products. Our Engineers are vast experienced in the field of manufacturing and assembling of electrical and electronic products. . We are confident about the quality of our products and trust that our products will be acceptable to you in all respect and we are assuring your best service. You can read more about Generator Checklist
Sincerely yours,
Md. Mahfuj Mondol
Executive (Sales & Service)
Cell:+8801704- 601875
*********************************** AB ENGINEERING & SERVICES
We manufacture and export below the CAD/CAM machines for garment, fashion, shoes and textile industry. They were sold in Europe, South Asia, Southeast Asia and so on. If you are interested in them, please approach us.
Digitizer (A0 and A00)
Inkjet plotter (printing width=1900mm to 2500mm)
Standing pattern cutting plotter (printing width=1200mm to 1900mm)
Flat bed pattern cutting plotter (size=1290 & 1512)
Standing & air flotation spreading tables (L=1.20m, W=to follow your sizes)
Band knife cutting machine (width=900mm & 1200mm)
laser cutting and engraving machine
We are offering below services:
Bulk SMS Service
IP PBX Solution/ FXS & FXO Gateway/ ATA Device/ IP Phone set
