• Ceramic Hot Plate – Sensor for medium temperature control • Rpm range from 0 to 1500 rpm • Max temperature of heating plate should be 550 °C • Low temperature stability • Heating Temperature display on LED • Speed display • Heating protection • Maximum Stirring Quantity IOL
This procedure applies to all contracts and
Product Specifications.
RESPONSIBILITY AND AUTHORITY
The Merchandising Manager, Cutting Room
Manager, Fabric Technologist & Pattern Technical Manager are responsible
for ensuring this procedure is adhered to.
PROCEDURE
2.8.1 Contract Control
Any amendment on product specifications is
received through e-mail from Head Office to the individual person who may
concern.
2.8.2 Cost Sheet
Amendment of the costing sheets are
recieved from head office to the cost accountant who then ensure to saved them
on costing amedment folder in common drive as PDF format.
Once saved to the common drive, it may
informe to relevant persons sendig a e-mail.
2.8.3 Pattern Amendments
Any pattern amendments to styles and new
patterns are received to the Costing Marker Maker and copied to the Pattern
Technical Manager. It is the
responsibility of Costing Marker Maker to ensure all relevant personnel receive
the relevant information.
Rockwell Plastics/Composite
(11Fta (Alpha), ISO 2039-2, ASTM
D785)
Scales: E, 1, M, R
Ball Indentation Plastics (ISO
2039-1)
Rockwell for Soft Metal
According to ISO 6508, ASTM E18
Scales: A 13CDEFGFIKLMN PRSTVW XY
Force Range
Preload
3kg,10kg
For Rockwell
15, 30, 45, 60, 100,150 kg
Rockwell Plastics/Composite 60. WO kg
Loading technology
Closed loop force control
Loading control (application, holding, and renlOval)
114mm diameter hardened and ground
anvil 230mm x 150mm rectangular hardened and ground anvil
6mm diameter spot and vet anvil
for 6-30mm diameter
specimens
Certification
13S EN ISO 6508-2, ASTM E18, UKAS
Test Blocks
UKAS Certified according to the following Scales and I lardness Values HRA Hardness Value 56 FIRE Hardness Value 92 HRE Hardness Value 100, 90, 75 I IRI. Hardness Value 123, 120,118 HRM Hardness Value 118, 112, 107 FIRR Hardness Value 126, 123,112
Electric pencil hardness tester
Test angle: 45 degrees
Load: Adjustable, 500g 250g 250g
Speed: 5mm / sec, adjustable
Travel distance: 40mm
Platform: about 12x17cm, can be fixed samples
Power: 220V / 50Hz
Accessories: Standard Pencil 6B ~ 6H each one, a total of 14 weights
As of November 2003, WRAP has over 700 international manufacturers with over 1300 participating factories in the program and has certified 570 factories. Certifications are valid for 12 months and all participating plants are subject to unannounced compliance inspections as mandated by the certification program. Many manufacturers have commented that WRAP has not only resulted in more reliable social compliance, but has contributed to greater productivity, lower turnover, improved communications between management and employees, safer working conditions and greately improved morale. Today, WRAP is being recognized by many retailers and manufacturers as the most reliable, yet economically efficient factory compliance system to assure lawful, ethical and humane manufacturing. The WRAP Good Factory Seal of Approval continues gain acceptance by sewn products manufacturers, retailers and governments around the globe.
Fusing bond test is very important for fusible interlining. Before operation the machine must be calibrated according to required bonding pressure. Improper bonding strength is the causes many types of defects such as glue stain; bubble etc. So it is very important to verify machine belt pressure before machine use. Read more about High Pressure Water Pump sss
Procedure
Use the tape in test kit and put into the claw of the
bonding tester. When tape goes into the machine completely and rated the value
from the scale. Hold the tape straight. Do the same procedure on the left, center
and right of the machine. The allowance
from the left to the right side should be within 20% from the total value. Make
sure that the distance between the bonding tester and the belt is always the
same.
Stainless steel rollers are
precision ground 420J2 stainless steel to prevent rust or erosion. The hardness is rated at 1-111.50-60 for reliable
long-life
usage.
Rolls are cored for either cooling for heating.
Manifold, valve, and collection
tank are standard. Rollers are ground to 5rim concentricity
and 0.5tun surface finish for precise applications
Compliance
More than three years ago, the industry began a process to demonstrate its commitment to responsible business practices and to ensure that apparel is produced under lawful, humane and ethical conditions. The process has reached out to many interested constituencies outside the apparel manufacturing community, including retailers, human rights advocates, public interest organizations, development agencies, and the licensing community.
The first result of this process was the development of the
Worldwide Responsible Apparel Production Principles – basic standards that
address labor practices, factory conditions, and environmental and customs
compliance. The WRAP Principles received the public endorsement of the AAMA
Board of Directors in 1998. More recently, the Principles have been endorsed by
groups representing apparel manufacturers from 18 countries around the world.
Global support for WRAP from consumers, manufacturers and governments grows
monthly. Recently, WRAP received the endorsement from manufacturers in Hong
Kong, Sri Lanka Pakistan, China, India and Guatemala. In November 2001, WRAP
welcomed the endorsement of the Textile and Apparel Manufacturers from Turkey.
In addition to the endorsement of the WRAP Principles, the
manufacturing associations and member manufacturing companies are actively
participating in the WRAP Certification Program. The WRAP Certification Program
is the only independent and globally supported factory certification program
requiring manufacturers to comply with the 12 universally accepted WRAP
Production Principles assuring safe and healthy workplace conditions, and
respect for workers’ rights.
