Automatic back pocket Blind Hem Stitch machine is applicable for jeans pant and other types of fabrics. The blind hemmer machine can process 8000 pockets per 10 hours. The efficiency of this machine is increased by twice compared with the traditional procedure. Differential feeding amount should be adjusted depending on kind of fabric elasticity. When hemming operation, especially on stepped parts, increasing amount than plain sewing will be sewn on stepped part better. Also beautiful finish can be obtained.
Blind Hem Manufacturing Requirements:
Must be even in width
Must be flat without twisting/ pleats
Must not have visible blind stitches on the product’s face side, if no other instruction has been given
Must stitching must overlap 2,5 cm to not unravel after wash
Specifications of Euromac Automatic Back Pocket Hemming Machine:
The efficiency is increased by twice compared with the traditional procedure
Blind Hem Guideline:
Before adjusting blind hem ALWAYS turn the motor switch OFF and check that the motor has already stopped.
Blind Hem Guideline
Set the left end of the slide edge guide 1. 5 mm inside that of the blind-hemming edge guide(1). Loosen the nut (3) and turn the adjusting screw (4) to adjust it.
Set the blind-hemming guide (2)2. 7 mm inside the left end of the blind-hemming edge guide(1). Loosen the screw(5) to adjust it.
Make the standard clearance between the sensor(6) and the right end of the blind-hemming guide(2) to 0. 8 mm.
Loosen the screw(7) to adjust it.
Adjust the clearance depending on the thickness of fabric or stepped size.
Increase the clearance when sewing heavy weight
Make the standard height of the blind-hemming edge guide from the top of the stitch plate to the bottom of the guide to 0. 1 mm. Too high position of it cannot detect the stepped part.
Loosen the screws(8)(9) and move CH device up or down to adjust it. After that, check the slide edge guide moves smoothly.
Blind Hem Sensitivity on Stepped Part:
Turn the sensitivity adjusting knob(1) to adjust the sensitivity depending on thickness of fabric.
When sewing heavy weight fabric, always the sensor detects and operate the slide edge guide, turn the knob to the left or to low number. When sewing light weight fabric, the sensor is difficult to detect the stepped part, turn the knob to the right or to high number. If the above adjusting fails to detect, make the clearance between the blind-hemming guide and the sensor to 0. 5 – 0. 7 mm. Note: Do not keep the detection lamp(2) turning on.
Blind Hem Stitch Depth on Stepped Part:
Adjust the stitch depth on the stepped part by operating amount of the slide edge guide. Standard amount is 2 mm. Loosen the nut(3) and turn the adjusting screw(4) to adjust it. To decrease the operating amount and make the stitch shallow, turn the adjusting screw(4) to the right.
Blind Hem Sensitivity
To increase the operating amount and make the stitch deep, turn the adjusting screw(4)to the left.
After adjusting, lock the adjusting screw(4) with the nut(3)
Stitch Number on Stepped Part of Joint Seam:
The operation count(front) (1) has been adjusted to “2” and operation count the (rear)(2) to “6” at shipment. When the sensor detects the stepped part, the slide edge guide moves to the right after two stitches. When the sensor finishes to detect the stepped part, it returns after six stitches.
Stepped Part of Joint Seam
Adjust the stitch number depending on the stitch length.
When much appeared stitches are many on a fabric before the stepped part, increase the number of the operation count (front)(1). If stitch depth is too shallow or off-stitch occurs, decrease the number.
When much appeared stitches are many on a fabric after the stepped part, decrease the number of the operation count (rear)(2). If stitch depth is too shallow or off-stitch occurs, increase the number.
Rotary Solenoid (large) and Blind Hem Guide:
The blind hemming guide can be put down until it is horizontally. Check it is tilted up enough when using.
Rotary Solenoid
Loosen the screw(1) and keep the guide tilted up. Turn the shaft(2) of the rotary solenoid (large) clockwise (seen from the shaft side) fully and fix it with the screw(1). And fix the hemming guide interlocking lever(3).
Blind Hem Rotation Detector Unit:
Do not put your foot on the pedal not to run a machine. Adjust the rotation detector unit so that the clock lamp(4) turns on when the needle tip is raised to the top of the stitch plate. Loosen the screw when the needle type is up to the top of the stitch plate. Align the magnet(5) of the oil cooling fan magnet unit with the rotation detector unit.
Blind Hem Rotation Detector
Blind Hem Foot:
Adjust the blind hem foot switch so that the presser foot lamp(1) turns on when the presser blind hem foot is raised though it turns off usually.
Blind Hem Foot
Make the clearance between the rotation detector unit(2) and the magnet(3) to 1.0 mm. Loosen the screw(5) and adjust the position of the magnet basement to move the switch plate(4) smoothly. Loosen the screw(6) and adjust the position of the switch plate(4) to move the presser blind hem foot lifter lever smoothly.
Detection of Stepped Part of Blind Hemmer:
When the sensor of blind hemmer is stayed, the detection lamp(1) turns on at the graduation “10” of the sensitivity adjusting knob (2) and turns off at “7” . Thees are correct positions of the side seam detector unit and the magnet. Turn the sensitivity adjusting knob(2) to “l” -“3” and push the sensor fully. The detection lamp (1) turns on.
Detection of Stepped Part
Loosen the screw(3) and turn the adjusting screw(4) to adjust up-and down position. To raise the side seam detector unit of blind hemmer and turn it clockwise. To lower the side seam detector unit, turn it counterclockwise.
Loosen the screw(5) and turn the adjusting screw(6) to adjust right-and-left position. To move the side seam detector unit to the left, turn it clokwise. To move the side seam detector unit to the right, turn it counterclockwise.
Note: If the detection lamp turns on when the sensor is pushed fully on the graduation “0” , adjust the variable resistor(7) in the control box as follows. Set the sensitivity adjusting knob to “1” and “2”. Turn the variable resistor(7) of blind hemmer to the right until the detection lamp turns off while pushing the sensor fully.
Sewing machine repair is the major factors now a day. We should assemble the sewing machine correctly. To prevent the overheat of needle point caused by the high speed sewing especially when it is made with synthetic threads and/or fabrics, HR unit is installed on the machine. Regular sewing machine repair makes the stitch skipping, thread breakage and such troubles as burning or enlargement of stitch hole on the fabric can be prevented. Oil should be used it is most effective to use those of Silicone Line. Check the quantity of oil occasionally, opening Lid (B). And replenish with new oil when it is running short.
Sewing Machine Repairs and Assemble SP Unit :
Like HR Unit, SP Unit is assembled and the sewing machine repairs as Standard Equipment, to prevent troubles resulting from heated needle.
SP Unit
We can expect an excellent effect by using HR and SP Units in combination. Oil those of Silicone Line is most effective as in the case of HR Unit. And check the quantity of oil in tank to sewing machine repairs occasionally and supply oil if necessary.
Overlocker Needle Setting :
There are many sizes of over locker needles, so select the suitable needle for sewing machine repair and maintenace. Basically speaking, No.8~11 should be used for light and medium materials and No.14 for heavy ones. Needle must be set correctly after confirming the direction, facing its scarf for the back side of machine as shown in the sketch.
Overlock Yamata Presser Foot:
The pressure of Presser Foot of overlock yamata will be strengthened by turning Adjusting Screw(A) to the right direction and weakened by turning it to the left.
Presser Foot
The pressure of Presser Foot should be adjusted most weakly so far as Presser Foot can act properly.
Adjustment of Width of Overlock Yamata Edge Seam :
To widen the width: Loosen the Screw(A) for Upper Knife Holder of overlock yamata and move the Holder to the direction (X) so far as the case needs, and tighten Screw (A) again. Then, loosen Screw(B) for Lower Knife Holder to enable to move to the direction (X) by the pressure of the Spring inside. Thus, Lower Knife will touch closely to Upper Knife(D) with the suitable strength. Keeping this condition, tighten Screw(B) again.
Adjustment of Width
To narrow the width: Loosen the Screw(B) for Lower Knife Holder and move the Holder to the direction (Y) so far as the case needs, and tighten Screw(B) softly. Then loosen Screw(A) for Upper Knife Holder and move this Holder to the direction(Y) to touch closely to Lower Knife(C), and tighten Screw(A) again. And then, loosen Screw(B) again and make the Lower Knife (C) touch with Upper Knife(D) by pressure of the Spring, and re-tighten Screw(B).
Note: In the adjustment for width of coveredge seam, the blade of Upper Knife must be positioned at about 1mm higher than that of Lower Knife as shown in the sketch.
Adjustment & Repair of Stitch Length:
How to change Stitch Length of overlocking . Pressing the Push button (A) with left hand until its finger will feel that the point of Button touches machine parts inside, then turn Pulley with right hand until the Button is fallen in. At this moment, press the Button more strongly to release engagement of Feed Dog Regulating Gear and continue the turning of Pulley.
Stitch Length
Graduations on the circumference of Pulley shows a Stitch Length in mm. Set any of Graduations as you desire with Countermark of Belt Cover(B), and then take the left hand off. There may be a little difference in the length owing to kind, thickness and differential ratio, in which cases Graduation must be readjusted suitably. Stitch length can be adjusted continuously from 1.0mm to 3.2mm.
Repair and Adjustment of Differential Feeding of Overlocking MC:
Normal Differential Feeding(Shrink Sewing): Loosen Nut(C) and decide the suitable position of Lever(D) by its up-and-down handling, then tighten Nut(C). When countermark of Lever is set with “2.3” of graduation, the ratio of differential feeding to main feeding becomes 1 : 2.3, and when it is set with “1” there is no differential feeding because of equal momentum. When the graduation on pulley is set at less than “2”, the differential ratio is available up to 1 : 2.3, and more than “2”, the ratio is up to 1 : 1.4.
Reverse Differential Feeding(Stretch Sewing): The reverse momentum will be increased with the lifting of Lever(D) from “1” to “S” on Graduation Plate(E). When the Countermark is set with “S”, the ratio of differential feeding to main feeding becomes 1 : 0.8.
Adjust the Differential Ratio of Over Lock Machine: To adjust the differential ratio while the machine is operating, connect the Chain to the Chain Hole on the Lever(D)
Tension of Overlocker Thread:
The standard position of Overlocker thread eyelet(A) is the position where the center of Screw(B) is aligned with Countermark(C). In case of stretchable thread chain, align the center with Countermark(D). When blind hemming work, raise Needle Thread Eyelet (A) to its highest point.
Tension of Overlocker Thread
Tension of Looper Overlocker Thread:
When turning Lower Looper Eyelet(A) to the direction (X), the lower looper thread slackens and to the direction(Y), it tightens.
When turning Thread Pull-off (B) to the direction (X), both upper and lower looper thread slacken and to the direction(Y), they tighten.
When moving Upper Looper overlocker thread Eyelet(C) to the direction(X) the upper looper thread slackens, and to the direction(Y) it tightens.
When moving Looper overlocker thread Pull-off (D) to the direction(X), upper looper thread slackens, and moving to the direction(Y), it tightens.
Over Lock Sewing Machine Repair and Checklist:
Check point (s )
Corrective action (s)
Check the lubrication system.
Oil filter.
Oil condition.
Oil level.
Amount of oil circulation.
Check all the oil pipes are not damaged. If damaged replace the oil pipes.
If the oil filter is clogged with heavy dust-clean it or replace it.
If the oil is dirty, change the oil & fill it up to a level between redlines.
Make sure that all the relevant parts are lubricated.
Check the feed system i.e. Feed dog, presser foot, needle plate.
If the feed dog teeth is worn out. Replace the feed dog.
If the presser foot is scratched. Buff the presser foot or replaces it.
Check the needle bar, needle bar bush. Needle holder.
If the play between needle bar and needle bar bush replace of repair them.
If needle holder is worn out, replace it.
Check the threading system i.e. Thread stand, thread tension post, different thread guides.
If the thread path is scratched or damaged smooth it by buffing of replace the thread guides.
Over all cleanliness
Clean the m/c by a soft bristle brush or a fabric (knitted / soft)
Check the electrical wiring, motor, etc
Take necessary action.
Check the safety devices i.e. Belt cover, eeshild etc.
Install the safety devices. If damaged by somehow.
Over Lock Machine Maintenance:
Daily Maintenance:
Done by : Operators
Supervised by: Maintenance Personnel
Needle Replacement: Check whether the needle is bent or blunt or not. If it is bent or blunt change the needle and install it under the supervision of maintenance personnel.
Looper:Clean the tail of thread, dust and lint in the looper.
Lubrication:Lubricate the machine parts where necessary.
Time required: 10 minutes.
Cleaning the looper case and other possible parts:Clean the lint, loose thread and other dirt from the shuttle of looper and looper case. Besides the table and other parts which cannot effect the setting must be cleaned.
Required time: 10 minute.
Weekly Maintenance:Done by : Maintenance Personnel
Supervised by: Maintenance Manager
Needle – Looper timing:Check whether the needle – looper timing is correct or not. If there lies miss-timing then adjust it.
The check points are
Needle – looper clearance
The height of needle from its lowest position of upward stroke when the looper reach at the center line of needle
At the same time the distance between the looper and the top end of the needle eye.
Required time: 10 minute.
The clearance between looper holder and looper case holder bracket: Check the clearance between the looper & looper case holder bracket (1-1.5mm). Make sure that the looper will not touch loooper case holder bracket.
Required time: 5 minute.
Presser foot pressure: Check whether the pressure of presser foot is proper or not. If not adjust it by adjusting the distance between the bottom washer and top of pressure bar guide bracket. And the bottom of work clamp must be kept parallel to the top of the work.
Required time: 5 minute.
Thread take-up amount: Check the amount of the thread take-up stroke, clearance between needle thread and thread take-up lever guide (0.5-1mm). Make sure that it is not more than necessary.
Required time: 5 minute.
Needle & looper thread tension adjustment: Check whether the standard operating range of thread take-up spring is accurate or not (6-8 mm). The tension at appropriate operating range must be checked.
Required time: 5 minute.
Needle installation: It must be remembered during needle installation that the long groove of the needle is on the left and tightened with the needle clamping screw. Adjust the needle clearance and lift amount.
Required time: 2 or 3 minute.
Stitch Length: Check whether the stitch length is appropriate or not. If not , slowly turn the hand wheel as you keep depressing push button and a point is found at which the push button goes further. With this condition, align the desired scale on the hand wheel with mark on the belt and reset the push button.
Required time: 5 minute.
Needle Bar height: It is remembered that when the needle bar is in its lowest position the reference line on the must be at the lower end of the containing the needle bar. If it is not so, remove the needle plate, loosen the needle bar connecting stud clamping screw and adjust by raising or lowering the needle bar.
Required time: 5 minute.
Adjustment of Pressure on the material (fabric): The pressure on the material during sewing must be as weak as possible, but strong enough so that the material does not slip. Adjust the pressure through loosing the adjustment nut.
Required time: 5 minute.
Feed Dog Height: The standard height of the feed dog for sewing thin material is 0.8 mm, and for medium material is .00 mm and for thick material is 1.2 mm (when the stitch length is set to the maximum).
Adjust the feed dog height by loosening the screw when the feed dog is above the needle plate surface and move the feed lifting arm up and down.
Rquired time: 5 minute.
Feed dog angle: In order to prevent puckering, material from slipping the feed dog is to be raised or lowered downward at standard angle.
When the feed dog angle has been adjusted, check to confirm that the height of feed dog has not changed.
Required time: 5 minute.
Presser foot height: The standard height of the presser foot is 6 mm when the presser foot is raised with presser foot lifter lever. To adjust the presser foot height, loosen the nut of the adjustment screw and then the presser foot adjustment screw so that no pressure will be applied to the presser foot, then loosen the set screw and adjust the presser foot height by raising or lowering the presser bar.
Required time: 5 minute.
Lubrication: Change oil when it contains contaminants. If the pointer bar of the oil gauge comes down under the lower marker line when the observing the sideward, supply oil. Change oil when one month has passed after the first set-up of machine. Apply two or three drops of oil to the needle bar and upper looper guide when operating the machine for the first time after set-up of after along time of disuse.
Caution: Be careful not to exceed the upper red marker line, or else troubles due to excessive lubrication may result.
Required time:5 minute.
Height of the lower knife: Loosening the set screw adjust the height of lower knife so that its edge is flush with the throat plate surface.
Height of the upper knife: Loosening the set screw perform the adjustment so that upper knife overlaps the lower knife 0.5-1 mm when the upper knife is at its lowest position.
Caution:
Be sure to tighten screw before operating machine.
After completion of adjustment, make the knives cut a thread to check sharpness of the knives.
Required time: 10 minute.
Sharpening the lower knife: When the lower knife has become dull, sharpen it.
Required time: 15 minute.
Monthly Maintenance:
Oil replacement and other interrelated checks:
Check lubricant or oil whether that is to replace.
Check bush leakage, oil seal leakage or age, vibration of oil and the flow of oil pump more or less than setting.
Check rubber cushion seats, four corners of machine tool groove on which oil pan stands.
Required time: 10 minute.
Rotary hook: Check rotary hook wear whether it is need to replace.
Required time: 10 minute.
Presser foot canal: Check its canal wear. If necessary replace it.
Required time: 5 minute.
Quarterly Maintenance:
Cleaning the filter and pump-net: Clean the filter and pump net to lengthen the machine life. If these are clogged with dust, the machine components may be seized or worn out extraordinarily.
Half yearly Maintenance:
Lubrication: Change oil of the machine every six month.
Adjustment OverlockerKnives for Fabric Cutting:
Different types of overlocker knives are described below shortly-
Lover Knife : The blade of Lover Knife (A) must be even with the top face of Stitch Plate or a little lower (0-‘-‘0.3 mm). To make this adjustment, loosen Screw(B).
Flat Upper Knife : As for the height of Flat Upper Knife, when this Knife reaches the bottom of its movement, make the engagement with Lower Knife be 0.5~1.0min. To make this adjustment, loosen Screw(C).
Over Lock Flat Upper Knife
Angled Upper Knife: Height of Angled Upper Knife is impossible to adjust as it is decided by Stopper(D) naturally. To set this Knife, loosen Screw(E) and insert the Knife to Upper Knife Holder until it will touch with Stopper(D), then tighten Screw(E) again.
Overlocking Angled Upper Knife
Sharpness of Knives: Turning the Pulley manually, after adjusting width of overedge seam, check the sharpness of Knives with a thread put between both Knives.
Re Sharpening OverlockerKnives: It is unnecessary to re sharpen Upper Knife for about one year as this Knife is made of Super Hard Alloy. During this period, if the cutting becomes blunt, Lower Knife must be sharpned as the sketch shows. As stated above, the Upper Knife cannot be re-sharpened by the ordinary grinder, abd the provisional one must be prepared always. For overlocker sewing machine repair and adjustment of parameters, please contact us directly or the dealer who sold the machine to you.
When the DVD of ModarisV5R1 is inserted in the PC an Autorun file will be executed that automatically open a folder. The man who will install can flow the setup guide in his chosen language. It describes the Modaris pattern software installation process and associated recommendations. It includes a ModarisV5R1 c3.exe file to directly pilot an automatic Modaris installation. A lot of applications installed by the Modaris installer. And includes another button Update Lectra workstation to allow upgrading other CAD workstations. Installation procedure of ModarisV7R2 is easier than Modaris V5R1
We have largest Garment and Textile ERP software collections in Bangladesh. We sale customized ERP for the factories. We are agent of all Garment and Textile ERP software company. We will forward you to the best ERP software company based on your requirements. We are trouble shooter of fashion industrial software like Willcom, Barudan, Lectra, How to install Lectra Plotter I Manager Software, Gerber, iEcho, Datacolor, Shedomaster, Batch, Qc etc. Email: [email protected], Cell: +88 017 92 52 53 54
How to install ModarisV5R1 Pattern Making Software:
First insert the Lectra CD into CDRom
Then go to the Lectra pattern making software Folder
Then click ModarisV5R1 .exe file
Then click Run Button to run the software
Then click Next Button for progressing the software
Then chose option button and click the I accept the terms of license agreement.
Then chose again option Typical or Custom. Generally select the Typical option. If you select you can install module by module according to your requirements
Then click again Next button again
Then click Finish Button. Now Your ModarisV5R1 pattern making modules installation is finished.
Update into Modaris V7R2:
The update procedure and location is described here shortly.
ModarisV7R2 Installer :
Modaris Installe provides an easy installation mode. This automatic Modaris installer file accessible from the setup guide that allows deploying required packages with one unique installer.
Pattern Making Software Free Modules:
After installing modaris v7r2 it will install more pattern making software free modules
Modaris: It is lectra pattern making software.
3D Prototyping: Lectra 3D Prototyping software.
Modaservice: Lectra service for Modaris data exchange.
JustPrint: Lectra plotting software.
E-Manager: It is another module of lectra
FLEXlm: It is another module of lectra
ButtonBox and Digitizer: These 2 modules are processed only when they are already deployed on the station
Upgrader:
The next automatic installer called Upgrader that is reachable through the Setup Guide. This upgrader is dedicated for all computers that are not Modaris stations. This upgrader need to be executed on CAD workstations used for plotting . This will ensure compatibility with applications installed by Modaris installer. It upgrades the following packages only if a previous release is already installed on the station.
Upgraded Free Pattern Making Doftware by Upgrader:
When ModarisV7R2 will upgrade it also generate some free pattern making software modules.
Modaservice: Lectra service unit to Modaris data exchange
XChang: Lectra software dedicated to Dxf data import in VigiPrint
Using Modaris installer and Upgrader apart from DVD:
At first copy all the installer folder tree from the DVD for guarantee a good deployment of Modaris installer and its modules. The following picture show within the red rectangle to the complete installer folder. After that execute Modaris installer that is running the following program: Packages\ModarisVxRy.exe or execute the Upgrader, running the following program: Packages\Related_Packages\Upgrader.exe
Installation Location:
By default, the installation folder is C:\Program Files\Lectra. To define a specific installation folder, for example: MY_INSTALLPATH, the command line will be: Package.exe■/v”INSTALLDIR=\”MY_INSTALLPATH\””
Note: “■” means a space character, “Package.exe” represents the package to install, “/v” is the option for defining parameters, “INSTALLDIR” is the MSI Value to define with the specific installation folder, Be careful to respect quotes””.
Example :
To install Modaris in following folder: “D:\ProgramFiles\Fashion_Solution”. The command line will be like this -Packages\ModarisVxRy.exe■/v”INSTALLDIR=\”D:\ProgramFiles\Fashion_Solution\””
To escape any dialog box requesting for a reboot you need to add the option “norestart” as shown in following command line: Package.exe■/v/norestart
Note: “■” means a space character and “Package.exe” represents the package to install and “/v” is the option for defining parameters, “/norestart” is the argument for avoiding reboot. The reboot prompt at the end of the Modaris Suite Installer deployment is due to a MSI Engine deployment. If MSI engine is not installed on the Operating System then it will be deployed by Lectra applications installation.
The concatenation of these options gives the following command line Package.exe■/v”/norestart■INSTALLDIR=\”MY_INSTALLPATH\””
Note: “■” means a space character where “Package.exe” represents the package to install and “/v” is the option for defining parameters. Always be careful to respect quotes””.
Example :
To install Modaris in following folder: “D:\ProgramFiles\Fashion_Solution”. The command line is:
Lectra Pattern Making Software Custom Installation:
Modaris installer and upgrader are the standard of Lectra software packages. They run stand alone packages normaly.If anybody want to create your own software scripts, it is mandatory to use the following stand alone packages instead of Modaris installer or upgrader. Here below the packages list of lectra pattern making software, the applications they install and their location on the DVD.
Modaris Software Evolution:
Modaris software evolution gives you access to the latest releases of Lectra solutions, allowing you to continually improve your technical performance and to optimize your best pattern design environment with each technological innovation. Modaris software evolution protects your investment over the long term. It makes savings while enabling you to maintain state of the art technology and systems.
Lectra Remote Expertise:
Lectra remote expertise offer global access to the experts and technical specialists via Lectra international call centers situated in Atlanta, USA (for North America); Bordeaux, France (for Europe); Madrid, Spain; Milan, Italy; and Shanghai, China (for Asia). The software as well as hardware can be accessed remotely by Lectra teams to provide real time IT solution for software problems production needs and workflow processes.
Lectra Consultation:
Lectra consultation services help you to identify difficulties related with your business as well as define environment for change in order to boost the creation of your products and reduce their time to market. The lectra teams of specialists will help you define priorities in terms of investments and prepare an action plan to speed up time to market, reduce costs, eliminate useless tasks and improve communication flows. On average, the lectrea specialists have more than 11 years of experience in garments and textile industry and in technology, which enables them to operate in each area of the consulting process, from audit to project implementation.
Training for Lectra Pattern Making Software :
Lectra provide training packages on lectra pattern making software you that will make optimal use of your software and equipment and will learn in record time. With more than 120 instructors, this training can be provided on site with customized programs or at one of Lectra training centers throughout the world. Chose the training modules best suited to your needs and combine them to create your own customized training program
Wilcom Tajima Barudan and other software company developed embroidery software for design. For more information please contact to us – Email: [email protected], Cell# 01792525354. Embroidery software is the leading application for embroidery industry design and manufacturer. Embroidery software is a set of clothes of CAD/CAM tools providing a first, flexible way to make, correct, organize and stitch out embroidery design. Embroidery software company is developing a lot of software module day by day.
List of Embroidery Software:
Wilcom Embroidery Software Modules
Wilcom Truesizer – Version 2006
Wilcom Decostudio – – Version 2006
DecoStudio Lite- Version 2006
DesignWorkflow- Version 2006
EmbroideryStudio- Version 2006
CorelDRAW X6- Version 2006
Tajima Embroidery Software Modules
Tajima DG/ML by Pulse
Tajima DG15 by Plus
PluseID Automation
PluseID Networking
PluseID API Toolkit
Barudan Embroidery Software Modules
TES V3 Modifier
TES Embroidery Studio Plus
TES V3 Creator
TES V3 Professional
TES V3 Viewer
Embird Embroidery Software Modules
Basic Embrid
Studio
Lettering windows fonts
Pattern manager and converter
Digitizing tools
Embroidery from photos
Icons from embroidery files
Cross stitch
Pre-digitized alphabet
Dakota Collectibles Modules
Annthegran Embroidery Software Modules
Janome Embroidery Software Modules
Bernina Embroidery Software Modules
Wilcom Embroidery Software:
It is design to carry the high output and efficiency requirements of professional digitizer. It also allows beginner and less frequent user to become productive digitizer. Wilcom lets you edit designs at any stages or adapt existing designs for use with different fabrics and machines.
Wilcom
Features of Wilcom Software:
Now anybody can view & change embroidery files.
FREE TrueSizer e3 desktop and web app now available in willcom office
View, modify, read and convert all major embroidery files with full design scalability. Use your PC
“The world’s favourite embroidery & apparel decoration software since 1979.”Get Help & Support
Wilcom is proudly Australian Software for better embroidery works
Tajima DG/ML by Pulse is the best embroidery software solution for your business in home and abroad. With higher lettering features, special stitch effects, and stylish embroidery creation from vectors, Tajima DG/ML by Pulse has all the tools you need to make attractive embroidery. The Using Tajima DG/ML by Pulse guide provides you with the information you need to learn about and begin using Tajima DG/ML by Pulse. For a full description of features available in each level, see our marketing brochures or talk to your distributor. For more information about Tajima DG/ML by Pulse, please visit our web site at www.pulsemicro.com.
Tajima
Most of the machine settings that were once found in Tools—Configuration—User Settings—Output to Embroidery Machine and Tools—Configuration—User Settings—Stitch Generation have been moved to a new design specific Machine Format settings. Now you can apply different machine settings for a selected type of embroidery machine. Settings such as the Maximum Stitch Length, Maximum Jump Length, and Number of jumps for a trim are now stored based on the type of machine you own. We provide default settings for many popular embroidery machine types. We will talk m ore about these settings later in this document.
Tajima Outline Processor:
Edition X supports a powerful Outline Processor that allows you to modify your designs to adjust their stitch count and other settings. With the outline processor, you can set a target stitch count (absolute or percentage) and the system will automatically adjust the values of settings for Fill (Tatami) and Satin density, Fill and Run stitch lengths, and Underlay Density. There are two modes for processing designs. In the Standard mode, the values of all settings are modified by the same proportion. For example if you set a target stitch count of 80%, the system will modify each setting value by 25%. In the Advanced mode, the system will modify each setting value by different percentages, with an effort to maintain overall stitch quality as close to the original design. To use the Outline Processor, follow the steps below:
Open an Outline based file by selecting File—Open
Select the segments you would like to work with using the Outline Processor or press CTRL + A to select all of the segments.
Select Tools—Outline Processor. You will see a dialog box similar to the one below
Embird Embroidery Software:
Embirdd is Machine Independent Embroidery Software. There are 70 embroidery file formats and 20 home and industrial machine brands supported. Embroidery designs digitizing, editing, organization, lettering and more. The Embird embroidery software is 64-bit and 32-bit Windows application for computer. This software is run on Windows 8, Windows 7, Vista, XP. Embird for Windows can be used also on Mac with OS X.
Embird
Parallels Desktop for Mac and Windows are required in this case. Software turns into FULL version only after registration. The Minimum hardware requirements is 1 Gb RAM, screen resolution 800×600, True Color display mode.
Barudan Embroidery Software:
Barudan
TES is Barudan Embroidery Software. Barudan Embroidery Software software is an integrated digitizing and editing system, fundamentally strong, reliable and complete for work. It builds the core platform for guiding the creation of embroidery at each stage, always ensuring higher quality results. It is available in dissimilar levels to cater for the varying needs of embroiderers. TES is designed to fit the needs of any user; from the very novice to the most experienced professional. It is completely modular and upgradeable from the entry level Modifier to the top of the line Professional.
Barudan TES Standard Features:
Open & Save designs in a variety of formats.
View designs in Realistic Mode – a three-dimensional thread simulation view.
Resize designs using Stitch Processing.
Clean up small stitches & jumps with Design Optimization to reduce thread breaks and sewing time.
Write designs directly to Barudan CF (Compact Flash) cards.
Send designs via e-mail with a single command.
Facilitate production set up with Production Worksheets.
View all design files quickly & easily with Design browser.
Set design colors choosing directly from thread manufacturers’ color palettes and assign needles on-screen when saving to Barudan formats with Design Color Management.
Before installing Lectra Diamino you should Install Lectra Modaris V7R2 pattern module software. This document is the installation roadmap for the current version of Lectra Diamino Fashion V6R1 and its components. Lectra recommend you to read it in full and print it so that you have it to hand during the installation process. To use Lectra Diamino Fashion V6R1, you must have the FLEXlm licenses for the use of the software. If you do not have these licenses, please contact Lectra to obtain them. To know more about Flexlm license installation, read the FLEXlm Setup Guidedocument (PDF format). The Diamino Fashion workstations should meet the following prerequisites hardware requirments: Central processing unit –CPU – 2.8 Ghz, RAM for Windows 7 Enterprise 32-bit & 64-bit- minimum 2Gb and optimum 3Gb, RAM for Windows Vista Enterprise 32-bit & 64-bit (SP1,SP2) et Windows Vista Business 32-bit & 64-bit (SP1,SP2)- – minimum 2Gb and optimum 3Gb, RAM for Windows XP Professional 32-bit Edition (SP2, SP3) – minimum 2Gb and optimum 3Gb, HDD free space- 0,9 Go for installation of application and components
We are the largest Garment and Textile ERP software collector in Bangladesh. We sale customized ERP for the factories. We are sole agent of all Garment and Textile ERP Software companies. We will forward you to the best ERP software company based on your requirements. We are trouble shooter of fashion industrial software like Willcom, Barudan, Lectra, Lectra Plotter I Manager Software Install, Gerber, iEcho, Datacolor, Shedomaster, Batch, Qc etc. Email: [email protected], Cell: +88 017 92 52 53 54
Uninstall The Previous Version of JustPrint:
Having JustPrint V2R2 and a previous version of JustPrint installed on the same workstation is not recommended. Before installing, uninstall the previous version of JustPrint (V1R1, V2R1 or V2R2):
Start a Windows session using an administrator account or a user account with administrator rights.
Go to Start->Settings->Control Panel and launch “Add or Remove Programs”.
In the “Currently installed programs” list, select the previous version of JustPrint, click on “Change/Remove” and follow the instructions
Applications of Lectra Diamino:
All necessary components will be installed if missing or updated to the latest version :
DiaminoFashion V6R1
Xchang V3R5
ButtonBox V1.1
Modaservice V7R1
JustPrint V2R2
Installation Procedure of Lectra Diamino Modaris V6r1 :
At first Exit all running applications to install Modaris V6r1
Open a Windows session with Administrator account or a admin user account with administrator rights.
Then click on the Diamino Fashion Installation
Then select Open or Run in the next window.
Select Run or Continue in the next window.
Click on Install to install the prerequisites.
Allow the workstation to prepare for installation (“Preparing to install…”)
Then click on Next in the first DiaminoFashion V6R1 Installer window.
Select I accept the terms of the license agreement
After that click on Next.
Then A window will appears offering to install your license files
If you have received your licenses:Check Install License Files,
If you have license in folder then the installation looks for the files on the desktop of the current user. If the license files are in a different folder, click on Browse to select the folder containing the license files, then on OK, Click Next,
Select Complete
Then click on Next
After that click on Install. The installation procedure may take a few minutes.
Installation may end with a dialog box asking if you want to restart your computer. We recommend that you select Yes to restart.
Finally click on “Finish“.
Configuration Other Lectra Workstations:
The other Lectra workstations where you use a Lectra application other than DiaminoFashion must be updated with the latest versions of Modaris V6r1 and XChang. Procedure of other Lectra workstations is given below:
First exit all running application software.
Then open a Windows session with administrator account or a admin user account with administrator rights.
First Insert the CD into CDRom
Then click on the “Update” button below
After that select “Open” or “Run” of the next window.
Then Select “Run” or “Continue” of the next window.
Then click on “Next” and “Install” in each window.
Supported Operating Systems for Diamino Modaris V6r1 :
Windows XP Professional (Service Pack 2, Service Pack 3)
Windows Vista Enterprise 32-bit & 64-bit Edition (Service Pack 1, Service Pack 2)
Windows Vista Business 32-bit & 64-bit Edition (Service Pack 1, Service Pack 2)
Windows 7 Enterprise 32-bit & 64-bit Edition
Licenses for Lectra Diamino Marker Making Software:
If you need any help please contact me in below mobile number. If you did not install the license files of DiaminoFashion marker making software and its components, you must install them onto your workstation when you receive them. For licence please visit For doing this, click on the ” Install license files ” button below and follow the procedure.
At first select Yes or Run when you are asked for confirmation.
Than select Browse for selecting the folder containing the license files,
Then click on Copy Files.
A message tells you how many license files were found in the folder and copied.
Finally click on OK to run marker making software.
