Tube Dispenser

  • Tube Dispenser -To disperse, stir and homogenize
  • Type: Tube or sonicator
  • Tank Volume max: 16 Liters or more Ultrasound frequency: 30 KHz or higher Speed (rpm) 400-6000
  • Carrying handles
  • Adjustable test duration
  • Pressure up to 7 bar or more Power: 0.46 HP
  • Voltage 220v ..

Sampling and Traditional Parameters

Installing light sources close to the work place is potentially profitable in case there are variations in the illumination required in the halls. In storage facilities this is usually not an option. Installing light switches in each hall and even over each working place is applicable when there are a number of halls for different production processes. It is not similar to Tubeless Lab Dispenser
The pay back time of this measure is usually between 1 and 3 years.
The International Commission on Illumination (CIE, and the International Standard Organization ISO have jointly published a standard governing lighting for indoor work places, taking into account energy efficiency. This standard ISO 8995:2002/CIE S 008/E:2001 called “Lighting of Indoor Work Places” may be obtained The member price is USD 51, whereas the list price

Parameter Limit Value
Temperature* ≤37℃*
pH, Standard Units 6.0-9.0
Total Suspended Solids (TSS) ≤30 ppm
Biological Oxygen Demand (BOD) ≤30 ppm
Chemical Oxygen Demand (COD) ≤200 ppm

*Should the facility be located in a region with an ambient temperature consistently above 37℃, the discharge temperature should be not exceed the temperature of the receiving body of water.

Chemical Constituents

Parameter Lower Limit Value
Antimony ≤0.50 ppm
Arsenic ≤0.01 ppm
Cadmium ≤0.01 ppm
Chromium ≤0.10 ppm
Cobalt ≤0.02 ppm
Copper ≤0.25 ppm
Cyanide ≤0.20 ppm
Lead ≤0.10 ppm
Mercury ≤0.01 ppm
Nickel ≤0.20 ppm
Zinc ≤1.00 ppm
Color ≤150 ADMI units OR 150 CO-PT units

Other Parameters

Parameter Limit or Requirement
Coliform 400 bacteria per 100ML
Foam No visible discharge of floating solids or persistent foam
Domestic Sewage All wastewater, including domestic sewage, must be properly treated before being discharged to the environment. If a public treatment facility is not available then the factory must properly treat sewage onsite before discharging.
Lab Equipment The facility shall have a pH meter, Imhoff Cone, and Thermometer in good working order.
Flow Meters The facility shall have, at a minimum, functioning flow meters are the input and output points of their wastewater treatment facility.

Applying Single Desizing

Cellulosics and their blends with synthetics could be desized, scoured and bleached in a single stage. This could reduce the processing time by a considerable extent, apart from reducing the water consumption and wastewater generation.

This measure has been implemented in number of units in India, particularly for the batches where the final dyed product is of a dark shade. In these situations no adverse effect on the quality was observed. The improved environmental impact is due to the fact that all three processes could be carried out in just one bath (instead of three different baths for thrice the duration and having rinses in between). Furthermore, as in earlier mentioned options, the industry concerned would need to make a few trials before commercial implementation.
Reduced process time and energy
Reduced water consumption
Reduced wastewater generation
Reduced cost of effluent treatment
Applicable for cellulosics and their blends only. Combined process for desizing, scouring and bleaching is particularly suitable for fabrics in dark shades, where the bleaching requirement is low. However, this could also be applied for medium shades, depending on the efficiency of the combined process.
The savings are obvious because of the reduction in the number of stages as well as the process time and water.


Tube Dispenser -Illegal discharge of wastewater or bypassing treatment facilities will not be tolerated