Flameability Tester
What is Flameability Tester

What is Flammability Testing Equipment?

Flammability Testing Equipment

Flammability Testing Equipment : Marker thread switch interchangeable test frame with frame stubs and pins

Finishing:  heat resistant finish

Ignition :automatic ignition

Control: burner to specimen adjustor

                gas flow regulator

                burner setting guages

Data extraction: test report exportation

Standards

  • EN ISO 6940
  • EN ISO 6941
  • EN ISO 15025
  • EN 1101,1102
  • EN 71-2
  • EN 13772
  • EN 13722
  • EN 1624
  • EN 1103
  • EN 14878
  • EN 1625
  • 85 EN 532
  • BS 7837,5722, 5867-2, 6249

Gas burners: range of gas burners as accessories to comply with all standards. Read about Yarn Evenness Tester

GENERAL FABRIC PROPERTIES

FIBRE REQUIREMENTS

Ramie –  Due to the flammable nature of this fibre it must not be used in any                 product for Adams Childrenswear.

Acetate – Due to performance issues satin fabrics made from acetate must not be used on Adams product.

YARN REQUIREMENTS

Cotton – Combed cotton yarns should only be used.

FABRIC REQUIREMENTS

Flammability- Due to potential flammability issues the following fabrics should be risk assessed by the Fabric Technology department prior to being used: 100% Cotton fabrics below 105g / m2  for full bodied skirts/dresses

100% Viscose fabrics below 120g / m2 for full bodied skirts/dresses

Fur/ Pile –  Fur fabrics must be back coated to assist in pile retention. Chemicals used must be in accordance with Chemical compliance table in Appendix 1 Pile length in excess of 3.5cm is not acceptable for garments intended for children aged between 9 months and 3 years.

Pile length in excess of 2cm is not acceptable in garments intended for children under 9 months.  All pile fabrics must be submitted to Auto Garments for approval of pile retention by the Fabric Technology Department.

Diamantes –  These must not be used for garments intended for children under 9 months old.

Only Diamantes purchased from Pacific Concept Industries/Heatseal are accepted for the age group between 9 months and 3 years. Further information can be obtained from the relevant departments.

In all cases the application method of the supplier should be followed and the applied diamantes must pass a motif/attachment durability test before acceptance of the order by Flammability Testing Equipment

Yellowing of White Color-

Definition and Causes

The yellowing of white fabrics that takes place after periodic exposure to light sources is normally caused by: The use of poor quality optical brighteners with poor light fastness properties, The incorrect PH levels of the fabric,The application of incorrect softeners.

The inter-action of one or a combination of any of the above with the Ultra Violet rays emitted by the sun or any other artificial sources will result in a semi-permanent yellowing of the exposed fabric.

Preventive Suggestions:All white fabrics, regardless of fiber type, must have PH levels of 5 to 6 (on the Acid side).

Corrective Measures

In most cases, a PH adjustment through rinsing will be sufficient to regain the brightness. In some cases a re-bleach may be required.Flammability Testing Equipment is essential for apparel company

About Engr. Kh. Mashiur Rahman

He is Top Class Digital Marketing Expert in bd based on Google Yahoo Alexa Moz analytics reports. He is open source ERP Implementation Expert for RMG Industry. He is certified IT Professional from Aptech, NCC, New Horizons & Post Graduated from London Metropolitan University (External) in ICT . To Hire his service and Him Email- sales@autogarment.com, Cell# +880 1792525354

Similar Post

Top 100 Yarn and Crochet Tools

Top 100 Yarn and Crochet Tools Crochet Tools What is Mohair Textile Yarn Tester? Type …

Leave a Reply

%d bloggers like this: